Layout and excavation
We mark the patio footprint, cut and remove sod or old concrete, and haul away debris. Subgrade is rough-graded to drain away from your house at 1 to 2 percent slope.
Licensed crews, code-correct pours, and finishes that handle San Diego County sun
Concrete Patio Installation Chula Vista CA built to last decades
Concrete Patio Installation Chula Vista CA is what we do every week, from Eastlake backyards to Otay Ranch pool decks. We form, pour, and finish patios that stay flat and crack-free through hot summers and winter rains. If you want a concrete patio pouring Chula Vista homeowners actually brag about, we give you a same-day estimate, a clear start date, and a crew that shows up when we say we will.
Careful work. Honest options.
About this service
Concrete Patio Installation Chula Vista CA done the right way
Concrete Patio Installation Chula Vista CA is the process of forming, reinforcing, pouring, and finishing a flat exterior slab that turns bare dirt or a worn-out deck into usable outdoor living space. We start with compacted base and proper grading, set 2x4 or 2x6 forms, tie rebar or wire mesh on chairs, then pour a 4-inch slab at 3,000 to 4,000 PSI. After that comes screeding, bull float work, edging, grooving control joints every 8 to 10 feet, and a cure that keeps the surface from drying too fast.
Most Chula Vista homeowners call us because their old patio is cracking, settling, or holding water against the house. Clay-heavy soil in older parts of town moves with the seasons, and a slab poured without proper base prep will curl and crack within a few years. Whether you need a new concrete patio Chula Vista California build or a full patio replacement Chula Vista CA job, we handle the tear-out, haul-away, and pour in one pass so you are not juggling three different crews.
- ✓ Decades of service life
- ✓ Lower cost than pavers or decking
- ✓ Slip-resistant and low-maintenance
- ✓ Adds real resale value
What's included
What is included in your concrete patio project
Every patio we pour includes the core work: layout, excavation, base prep, forming, reinforcement, the pour, finishing, and cleanup. Add-ons like stamped finishes, integral color, and retaining walls are quoted separately so you can see exactly what each upgrade costs. Here is what the base scope covers.
Compacted base and forms
We compact 2 to 4 inches of base material, set forms to final grade, and check slope with a level and string line before any concrete shows up on site.
Rebar or wire mesh
Standard patios get wire mesh on proper overlap. Patios over 400 square feet or on soft soil get a #3 or #4 rebar mat tied on chairs for real structural reinforcement.
Concrete pour and finish
We place 3,500 to 4,000 PSI concrete, screed, bull float, edge, and cut control joints every 8 to 10 feet. Finish options include broom, smooth trowel, stamped, or exposed aggregate.
Curing and cleanup
We apply curing compound, protect the slab from foot traffic for 24 to 48 hours, and clean the site. You get a walkthrough and care instructions before we leave.
How it works
How our concrete patio pouring process works
We walk the yard with you, check slope away from the house, look at soil and access for the truck, and measure the actual square footage. You get a written number the same day, usually within two hours of the visit. No pressure, no deposit to get a quote.
We mark the patio outline with string lines and paint, then cut and remove sod or old concrete. Depending on size, excavation takes half a day to a full day. We haul away debris and rough-grade the subgrade so water sheds away from your foundation at a 1 to 2 percent slope.
We compact 2 to 4 inches of base, set forms to final grade, and tie #3 or #4 rebar on chairs or lay wire mesh. For patios over 400 square feet or on soft soil, we add rebar mats. We call for inspection if your project needs a permit, then schedule the pour.
The concrete truck arrives, and we place the mix at 3,500 to 4,000 PSI. We screed, bull float, edge, and cut control joints every 8 to 10 feet. Finish options include broom, smooth trowel, stamped, or exposed aggregate. Pour and finish typically take four to six hours for a standard patio.
We apply curing compound and keep foot traffic off for 24 to 48 hours. You can park furniture on it after 7 days and drive on it after 28. We walk the finished slab with you, point out control joints and drainage, and hand over care instructions.
STEP 01Site walk and estimate
We walk the yard with you, check slope away from the house, look at soil and access for the truck, and measure the actual square footage. You get a written number the same day, usually within two hours of the visit. No pressure, no deposit to get a quote.
Tools & methods
Tools and methods we use on every pour
Concrete mixer and pump truck
We use a concrete pump for backyard pours with no truck access, and a mixer for small patches and repairs. Pumping avoids cold joints and saves hours of wheelbarrow work.
Power trowel and bull float
The bull float knocks down the initial pour and brings cream to the surface. The power trowel gives a hard, smooth finish on interior-grade slabs and covered patios.
Concrete saw and groover
We cut control joints with a groover during the pour and a concrete saw for expansion joints and openings. Proper joint spacing is what keeps random cracks from forming.
Rebar cutter and vibrator
The rebar cutter keeps our reinforcement clean and to length. The vibrator removes air pockets from the mix so the slab consolidates properly around rebar and edges.
Screed and edger
The screed levels the concrete to the form height. The edger rounds the slab edge so it does not chip and looks finished from the side.
Hilti and Bosch rotary hammers
We use Hilti and Bosch rotary hammers for drilling anchor holes, tying into existing slabs, and setting dowels when a new patio meets old concrete.
Real results
Before and after.
Concrete Patio Installation
Cracked 1990s patio replaced in Castle Park
A 280-square-foot patio poured in the 1990s had three major cracks, spalling along the edges, and water pooling against the back door every winter. The homeowner was ready to replace it after two failed patch jobs.
After: We tore out the old slab, removed 5 inches of clay, compacted new base, and poured a 4-inch reinforced slab with a broom finish and control joints every 8 feet. Total project took three days. The new patio drains away from the house and carries our five-year workmanship warranty.
Book this service →
Concrete Patio Installation
New stamped pool deck in Eastlake
A family in Eastlake had a new pool installed but the surrounding yard was bare dirt and mud. They wanted a deck that matched the pool coping, stayed cool underfoot, and passed inspection without delays.
After: We poured a 620-square-foot stamped deck in a slate pattern with integral color and a slip-resistant release. The deck slopes to two deck drains and meets ADA transition requirements at the steps. The inspector passed it on the first visit.
Book this service →
Concrete Patio Installation
Sloped Rancho del Rey yard turned into usable patio
A Rancho del Rey homeowner had a backyard that dropped 3 feet from the house to the fence. The lower half was unusable and eroded every time it rained. They wanted a flat patio and a way to hold the slope.
After: We poured a 24-inch reinforced retaining wall with weep holes and drainage gravel, backfilled and compacted, then poured a 340-square-foot patio on top. The patio ties into the wall and slopes away from the house. Project took five days start to finish.
Book this service → Problems we solve
Concrete patio problems we fix in Chula Vista
Old patios fail in predictable ways. Here are the most common calls we get and how we handle them.
Ask a pro →Cracked and settling patio slab
We cut out the failed sections or remove the whole slab, re-compact the base, and pour fresh concrete with proper reinforcement and control joints. If the slab is still solid but sunken, we can lift it with mudjacking instead of replacing it.
Water pooling against the house
We re-grade the patio to a 1 to 2 percent slope away from the house and pour a new slab that sheds water correctly. If drainage is a bigger issue, we can add a channel drain or tie into your existing yard drainage.
Spalling and surface scaling
We grind and resurface the slab with a polymer-modified overlay, or if the damage is deep, we replace the affected sections. New pours get proper mix design and curing to prevent the problem from coming back.
Efflorescence and white staining
We clean the surface with a mild acid wash, then apply a breathable sealer that lets moisture escape without leaving salt deposits. If the slab is new, we adjust the cure schedule to prevent it in the first place.
Transparent pricing
What concrete patio installation costs in 2026
$4,800 - $18,000 depending on size, finish, and site conditions
Typical 2026 pricing for a concrete patio in Chula Vista runs $16 to $30 per square foot installed, depending on finish, thickness, site access, and whether we are tearing out an old slab. A standard 300-square-foot broom-finish patio usually lands between $4,800 and $9,000. Stamped and exposed-aggregate finishes push toward the higher end. We quote every job in writing after a free on-site walk, so you see the line items before you commit. No hidden fees, no surprise change orders.
A patio is one of the few home improvements that pays you back every weekend. It adds usable outdoor square footage, improves drainage around your foundation, and lasts 30-plus years with minimal care. Compare that to a wood deck that needs staining every two years or pavers that shift and grow weeds.
•affects cost
Price scales with area, but larger patios cost less per square foot because mobilization and setup are spread across more concrete. A 600-square-foot patio often costs less per foot than a 150-square-foot one.
Get a quote ↗•affects cost
Broom finish is the most affordable. Stamped, exposed aggregate, and integral color add labor and materials, usually $4 to $10 per square foot more depending on pattern complexity and color choices.
Get a quote ↗•affects cost
Removing an old slab adds $2 to $5 per square foot for cutting, breaking, loading, and disposal. We include dump fees in the quote so there is no surprise at the end.
Get a quote ↗•affects cost
If a concrete truck cannot reach the pour site, we bring a pump, which adds $800 to $1,500 depending on distance and hose length. Tight side yards and steep slopes also add labor.
Get a quote ↗ Proof you can check
Licensed, insured, and warrantied
- California Contractors State License Board (CSLB) License · State of California
- ACI Certification · American Concrete Institute
- OSHA 30 Training · Occupational Safety and Health Administration
- NRMCA Certification · National Ready Mixed Concrete Association
- Full Liability and Workers Compensation Insurance · State of California
Customer reviews
What Chula Vista homeowners say
★★★★★
“We had a 400-square-foot stamped patio poured in our Eastlake backyard. The crew showed up at 6:30 a.m. on pour day, had the truck placed by 8, and finished the stamp work by early afternoon. Two years later, not a single crack outside the control joints. They also fixed a sprinkler line they hit during excavation without charging us extra.”
MR
Marisol R.Homeowner, Eastlake
✓ Verified“
★★★★★
“Our old patio was cracked and pooling water against the house. OR Concrete tore it out, re-graded the yard, and poured a new 350-square-foot broom-finish slab. The slope is right, water runs away from the foundation, and the price came in exactly where they quoted. No surprises.”
DK
Dave K.Homeowner, Otay Ranch
✓ Verified★★★★★
“We needed a patio and a small retaining wall because our yard slopes. They poured both in the same week and tied the wall drainage into the patio slope. The inspector passed it first time. The crew cleaned up every day and our dog never got out. Highly recommend.”
PS
Priya S.Homeowner, Rancho del Rey
✓ VerifiedMost patios in Chula Vista run $16 to $30 per square foot in 2026, so a 300-square-foot slab lands between $4,800 and $9,000. Broom finish sits at the low end, stamped or exposed aggregate at the high end. Tear-out of an old slab, tight access, and complex shapes add cost. We give you an exact number after a free on-site walk.
A standard 300-square-foot patio takes two to three days from excavation to finished pour. Day one is demo and grading, day two is forming and rebar, day three is the pour and finish. You can walk on it after 24 to 48 hours and put furniture back after 7 days. Larger or stamped patios may add a day.
The right contractor is licensed, insured, and willing to show you past work in your neighborhood. We have poured patios in Chula Vista since 2018, carry an active CSLB license, and back our work with a five-year workmanship warranty. Ask any contractor for their license number and two local references before you sign.
Most flat, on-grade residential patios under 30 inches tall do not need a permit in Chula Vista. You do need one if the patio is raised, tied into a retaining wall, or part of a covered structure. We handle the permit paperwork and inspection scheduling when your project requires it, so you are not chasing the city.
Ready when you are
Get your Concrete Patio Installation Chula Vista CA quote today
We give free on-site estimates and written pricing the same day. Licensed, insured, and backed by a five-year workmanship warranty. Call us at (619) 984-3356 and we will schedule your walk-through this week.
Get Free Estimate +16199843356 →
Request an appointment
Contact Our Chula Vista Concrete Crew
Call us at +1 (619) 984-3356 and we will get you on the schedule. Most estimates go out the same day, and we answer questions about thickness, finish, and cure times before you commit to anything. Reach us by phone or email, Monday through Friday, 8:00 to 18:00.
Call anytime+16199843356Email the officeinfo@orconcretecontractorchulavista.site
Office hoursOpen 24 hours · 7 days a week